External Memory Interfaces (EMIF) IP User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 817467
Date 4/01/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the External Memory Interfaces Agilex™ 5 FPGA IP 2. Agilex™ 5 FPGA EMIF IP – Introduction 3. Agilex™ 5 FPGA EMIF IP – Product Architecture 4. Agilex™ 5 FPGA EMIF IP – End-User Signals 5. Agilex™ 5 FPGA EMIF IP – Simulating Memory IP 6. Intel® Agilex™ 5 FPGA EMIF IP - DDR4 Support 7. Intel® Agilex™ 5 FPGA EMIF IP - LPDDR4 Support 8. Intel® Agilex™ 5 FPGA EMIF IP - LPDDR5 Support 9. Agilex™ 5 FPGA EMIF IP – Timing Closure 10. Agilex™ 5 FPGA EMIF IP – Controller Optimization 11. Agilex™ 5 FPGA EMIF IP – Debugging 12. Document Revision History for External Memory Interfaces (EMIF) IP User Guide
1. About the External Memory Interfaces Agilex™ 5 FPGA IP x
1.1. Release Information
2. Agilex™ 5 FPGA EMIF IP – Introduction x
2.1. Agilex™ 5 EMIF IP Protocol and Feature Support 2.2. Agilex™ 5 EMIF IP Design Flow
2.2. Agilex™ 5 EMIF IP Design Flow x
2.2.1. Agilex™ 5 EMIF IP Design Checklist
3. Agilex™ 5 FPGA EMIF IP – Product Architecture x
3.1. Agilex™ 5 EMIF Architecture: Protocol and Maximum Interface Width Support 3.2. Agilex™ 5 EMIF Architecture: Introduction 3.3. Agilex™ 5 EMIF Sequencer 3.4. Agilex™ 5 EMIF Controller 3.5. Agilex™ 5 EMIF IP for Hard Processor Subsystem (HPS)
3.2. Agilex™ 5 EMIF Architecture: Introduction x
3.2.1. Agilex™ 5 EMIF Architecture: I/O Subsystem 3.2.2. Agilex™ 5 EMIF Architecture: I/O SSM 3.2.3. Agilex™ 5 EMIF Architecture: HSIO Bank 3.2.4. Agilex™ 5 EMIF Architecture: I/O Lane 3.2.5. Agilex™ 5 EMIF Architecture: Input DQS Clock Tree 3.2.6. Agilex™ 5 EMIF Architecture: PHY Clock Tree 3.2.7. Agilex™ 5 EMIF Architecture: PLL Reference Clock Networks 3.2.8. Agilex™ 5 EMIF Architecture: Clock Phase Alignment 3.2.9. User Clock in Different Core Access Modes
3.2.3. Agilex™ 5 EMIF Architecture: HSIO Bank x
3.2.3.1. Pin Placement 3.2.3.2. HSIO Sub-Bank Usage
3.3. Agilex™ 5 EMIF Sequencer x
3.3.1. Agilex™ 5 Mailbox Structure and Register Definitions
3.3.1. Agilex™ 5 Mailbox Structure and Register Definitions x
3.3.1.1. Mailbox Supported Commands 3.3.1.2. Mailbox Command Definitions
3.4. Agilex™ 5 EMIF Controller x
3.4.1. Hard Memory Controller
3.4.1. Hard Memory Controller x
3.4.1.1. Hard Memory Controller Features
4. Agilex™ 5 FPGA EMIF IP – End-User Signals x
4.1. Agilex™ 5 FPGA EMIF IP Interfaces for DDR4 4.2. Agilex™ 5 FPGA EMIF IP Interfaces for LPDDR4 4.3. Agilex™ 5 FPGA EMIF IP Interfaces for LPDDR5 4.4. Agilex™ 5 FPGA EMIF IP Interfaces for EMIF Calibration Component
4.1. Agilex™ 5 FPGA EMIF IP Interfaces for DDR4 x
4.1.1. ref_clk for EMIF 4.1.2. core_init_n for EMIF 4.1.3. usr_async_clk for EMIF 4.1.4. usr_clk for EMIF 4.1.5. usr_rst_n for EMIF 4.1.6. s0_axi4 for EMIF 4.1.7. mem for EMIF 4.1.8. oct for EMIF
4.2. Agilex™ 5 FPGA EMIF IP Interfaces for LPDDR4 x
4.2.1. ref_clk for EMIF 4.2.2. core_init_n for EMIF 4.2.3. usr_async_clk for EMIF 4.2.4. usr_clk for EMIF 4.2.5. usr_rst_n for EMIF 4.2.6. s0_axi4 for EMIF 4.2.7. mem for EMIF 4.2.8. oct for EMIF
4.3. Agilex™ 5 FPGA EMIF IP Interfaces for LPDDR5 x
4.3.1. ref_clk for EMIF 4.3.2. core_init_n for EMIF 4.3.3. usr_async_clk for EMIF 4.3.4. usr_clk for EMIF 4.3.5. usr_rst_n for EMIF 4.3.6. s0_axi4 for EMIF 4.3.7. oct for EMIF
4.4. Agilex™ 5 FPGA EMIF IP Interfaces for EMIF Calibration Component x
4.4.1. s0_axi4lite_clk for EMIF 4.4.2. s0_axi4lite_rst_n for EMIF 4.4.3. s0_axil for EMIF
5. Agilex™ 5 FPGA EMIF IP – Simulating Memory IP x
5.1. Simulation Walkthrough
5.1. Simulation Walkthrough x
5.1.1. Calibration 5.1.2. Simulation Scripts 5.1.3. Functional Simulation with Verilog HDL 5.1.4. Simulating the Design Example
6. Intel® Agilex™ 5 FPGA EMIF IP - DDR4 Support x
6.1. Intel® Agilex™ 5 FPGA EMIF IP Parameters for DDR4 6.2. Agilex™ 5 FPGA EMIF IP Pin and Resource Planning 6.3. Agilex™ 5 EMIF Pin Swapping Guidelines 6.4. DDR4 Layout Design Guidelines
6.1. Intel® Agilex™ 5 FPGA EMIF IP Parameters for DDR4 x
6.1.1. Agilex™ 5 FPGA EMIF IP Parameter for DDR4 6.1.2. Intel Agilex 5 FPGA EMIF Memory Device Description IP (DDR4) Parameter Descriptions
6.2. Agilex™ 5 FPGA EMIF IP Pin and Resource Planning x
6.2.1. Intel® Agilex™ 5 FPGA EMIF IP Resources 6.2.2. Pin Guidelines for Intel® Agilex™ 5 FPGA EMIF IP 6.2.3. Pin Placements for Intel® Agilex™ 5 FPGA DDR4 EMIF IP
6.2.1. Intel® Agilex™ 5 FPGA EMIF IP Resources x
6.2.1.1. OCT 6.2.1.2. PLL
6.2.2. Pin Guidelines for Intel® Agilex™ 5 FPGA EMIF IP x
6.2.2.1. Intel® Agilex™ 5 FPGA EMIF IP Pin and Resource Planning
6.2.2.1. Intel® Agilex™ 5 FPGA EMIF IP Pin and Resource Planning x
6.2.2.1.1. Intel® Agilex™ 5 FPGA EMIF IP Interface Pins 6.2.2.1.2. Estimating Pin Requirements 6.2.2.1.3. Maximum Number of Interfaces
6.2.3. Pin Placements for Intel® Agilex™ 5 FPGA DDR4 EMIF IP x
6.2.3.1. Address and Command Pin Placement for DDR4 6.2.3.2. DDR4 Data Width Mapping 6.2.3.3. General Guidelines 6.2.3.4. Specific Pin Connection Requirements 6.2.3.5. Command and Address Signals 6.2.3.6. Clock Signals 6.2.3.7. Data, Data Strobes, DM/DBI, and Optional ECC Signals
6.3. Agilex™ 5 EMIF Pin Swapping Guidelines x
6.3.1. DDR4 Byte Lane Swapping 6.3.2. DDR4 Address and Command and CLK Lane 6.3.3. DDR4 Interface x8 Data Lane 6.3.4. DDR4 Interface x4 Data Lane
6.4. DDR4 Layout Design Guidelines x
6.4.1. DDR4 PCB Stackup and Design Considerations 6.4.2. DDR4 General Design Considerations 6.4.3. DDR4 Routing Guidelines - Memory-Down (Discrete) Topologies
6.4.3. DDR4 Routing Guidelines - Memory-Down (Discrete) Topologies x
6.4.3.1. 1 Rank x 8 Discrete (Memory Down) Topology 6.4.3.2. 1 Rank x 16 Discrete (Memory Down) Topology 6.4.3.3. VREF_CA/RESET Signal Routing Guidelines for 1 Rank x 8 and 1 Rank x 16 Discrete (Memory Down) Topology 6.4.3.4. Skew Matching Guidelines for DDR4 (Memory Down) Discrete Configurations 6.4.3.5. Power Delivery Recommendation for DDR4 Discrete Configurations 6.4.3.6. DDR4 Simulation Strategy
7. Intel® Agilex™ 5 FPGA EMIF IP - LPDDR4 Support x
7.1. Intel® Agilex™ 5 FPGA EMIF IP Parameters for LPDDR4 7.2. Intel® Agilex™ 5 FPGA EMIF IP Pin and Resource Planning 7.3. LPDDR4 Layout Design Guidelines
7.1. Intel® Agilex™ 5 FPGA EMIF IP Parameters for LPDDR4 x
7.1.1. Agilex™ 5 FPGA EMIF IP Parameter for LPDDR4 7.1.2. Intel Agilex 5 FPGA EMIF Memory Device Description IP (LPDDR4) Parameter Descriptions
7.2. Intel® Agilex™ 5 FPGA EMIF IP Pin and Resource Planning x
7.2.1. Intel® Agilex™ 5 FPGA EMIF IP Interface Pins 7.2.2. Intel® Agilex™ 5 FPGA EMIF IP Resources 7.2.3. Pin Guidelines for Intel® Agilex™ 5 FPGA EMIF IP
7.2.1. Intel® Agilex™ 5 FPGA EMIF IP Interface Pins x
7.2.1.1. Estimating Pin Requirements 7.2.1.2. LPDDR4 Component Options 7.2.1.3. Maximum Number of Interfaces
7.2.2. Intel® Agilex™ 5 FPGA EMIF IP Resources x
7.2.2.1. OCT 7.2.2.2. PLL
7.2.3. Pin Guidelines for Intel® Agilex™ 5 FPGA EMIF IP x
7.2.3.1. General Guidelines 7.2.3.2. Specific Pin Connection Requirements 7.2.3.3. Command and Address Signals 7.2.3.4. Clock Signals 7.2.3.5. Address and Command Pin Placement for LPDDR4 7.2.3.6. Pin Placements for Agilex™ 5 FPGA EMIF IP for LPDDR4 7.2.3.7. Pin Swapping Guidelines
7.3. LPDDR4 Layout Design Guidelines x
7.3.1. LPDDR4 PCB Stackup and Design Considerations 7.3.2. LPDDR4 General Design Considerations 7.3.3. LPDDR4 Interface Design Guidelines
7.3.3. LPDDR4 Interface Design Guidelines x
7.3.3.1. LPDDR4 Discrete Component/Memory Down Topology (up to 32 bits interface) 7.3.3.2. LPDDR4 Simulation Strategy
8. Intel® Agilex™ 5 FPGA EMIF IP - LPDDR5 Support x
8.1. Intel Agilex 5 FPGA EMIF IP Parameters for LPDDR5 8.2. Agilex™ 5 FPGA EMIF IP Pin and Resource Planning 8.3. LPDDR5 Layout Design Guidelines
8.1. Intel Agilex 5 FPGA EMIF IP Parameters for LPDDR5 x
8.1.1. Agilex™ 5 FPGA EMIF IP Parameter for LPDDR5 8.1.2. Intel Agilex 5 FPGA EMIF Memory Device Description IP (LPDDR5) Parameter Descriptions
8.2. Agilex™ 5 FPGA EMIF IP Pin and Resource Planning x
8.2.1. Agilex™ 5 FPGA EMIF IP Interface Pins 8.2.2. Agilex™ 5 FPGA EMIF IP Resources 8.2.3. Pin Guidelines for Agilex™ 5 FPGA EMIF IP 8.2.4. Pin Placements for Intel Agilex 5 FPGA LPDDR5 EMIF IP
8.2.1. Agilex™ 5 FPGA EMIF IP Interface Pins x
8.2.1.1. Estimating Pin Requirements 8.2.1.2. LPDDR5 Component Options 8.2.1.3. Maximum Number of Interfaces
8.2.2. Agilex™ 5 FPGA EMIF IP Resources x
8.2.2.1. OCT 8.2.2.2. PLL
8.2.3. Pin Guidelines for Agilex™ 5 FPGA EMIF IP x
8.2.3.1. General Guidelines - LPDDR5 8.2.3.2. Specific Pin Connection Requirements 8.2.3.3. Command and Address Signals 8.2.3.4. Clock Signals
8.2.4. Pin Placements for Intel Agilex 5 FPGA LPDDR5 EMIF IP x
8.2.4.1. Address and Command Pin Placement for LPDDR5 8.2.4.2. LPDDR5 Data Width Mapping 8.2.4.3. LPDDR5 Byte Lane Swapping
8.3. LPDDR5 Layout Design Guidelines x
8.3.1. LPDDR5 PCB Stackup and Design Considerations 8.3.2. LPDDR5 General Design Considerations 8.3.3. LPDDR5 Interface Design Guidelines
8.3.3. LPDDR5 Interface Design Guidelines x
8.3.3.1. LPDDR5 Discrete Component/Memory Down Topology (Single Rank or Dual-Rank) 8.3.3.2. Example of an LPDDR5 Layout on an Intel FPGA Platform Board 8.3.3.3. LPDDR5 Simulation Strategy
9. Agilex™ 5 FPGA EMIF IP – Timing Closure x
9.1. Timing Closure 9.2. Optimizing Timing
9.1. Timing Closure x
9.1.1. Timing Analysis
9.1.1. Timing Analysis x
9.1.1.1. PHY or Core
10. Agilex™ 5 FPGA EMIF IP – Controller Optimization x
10.1. Interface Standard 10.2. Bank Management Efficiency 10.3. Data Transfer 10.4. Improving Controller Efficiency
10.4. Improving Controller Efficiency x
10.4.1. Frequency of Operation 10.4.2. Series of Reads or Writes
11. Agilex™ 5 FPGA EMIF IP – Debugging x
11.1. Interface Configuration Performance Issues 11.2. Functional Issue Evaluation 11.3. Timing Issue Characteristics 11.4. Verifying Memory IP Using the Signal Tap Logic Analyzer 11.5. Generating Traffic with the Test Engine IP 11.6. Guidelines for Developing HDL for Traffic Generator 11.7. Hardware Debugging Guidelines 11.8. Create a Simplified Design that Demonstrates the Same Issue 11.9. Measure Power Distribution Network 11.10. Measure Signal Integrity and Setup and Hold Margin 11.11. Vary Voltage 11.12. Operate at a Lower Speed 11.13. Determine Whether the Issue Exists in Previous Versions of Software 11.14. Determine Whether the Issue Exists in the Current Version of Software 11.15. Try A Different PCB 11.16. Try Other Configurations 11.17. Debugging Checklist 11.18. Categorizing Hardware Issues 11.19. Signal Integrity Issues 11.20. Characteristics of Signal Integrity Issues 11.21. Evaluating Signal Integrity Issues 11.22. Skew 11.23. Crosstalk 11.24. Power System 11.25. Clock Signals 11.26. Address and Command Signals 11.27. Read Data Valid Window and Eye Diagram 11.28. Write Data Valid Window and Eye Diagram 11.29. Hardware and Calibration Issues 11.30. Memory Timing Parameter Evaluation 11.31. Verify that the Board Has the Correct Memory Component or DIMM Installed
11.1. Interface Configuration Performance Issues x
11.1.1. Interface Configuration Bottleneck and Efficiency Issues
11.2. Functional Issue Evaluation x
11.2.1. Intel® IP Memory Model 11.2.2. Vendor Memory Model 11.2.3. Transcript Window Messages
11.3. Timing Issue Characteristics x
11.3.1. Evaluating FPGA Timing Issues 11.3.2. Evaluating External Memory Interface Timing Issues
1. About the External Memory Interfaces Agilex™ 5 FPGA IP
2. Agilex™ 5 FPGA EMIF IP – Introduction
3. Agilex™ 5 FPGA EMIF IP – Product Architecture
4. Agilex™ 5 FPGA EMIF IP – End-User Signals
5. Agilex™ 5 FPGA EMIF IP – Simulating Memory IP
6. Intel® Agilex™ 5 FPGA EMIF IP - DDR4 Support
7. Intel® Agilex™ 5 FPGA EMIF IP - LPDDR4 Support
8. Intel® Agilex™ 5 FPGA EMIF IP - LPDDR5 Support
9. Agilex™ 5 FPGA EMIF IP – Timing Closure
10. Agilex™ 5 FPGA EMIF IP – Controller Optimization
11. Agilex™ 5 FPGA EMIF IP – Debugging
12. Document Revision History for External Memory Interfaces (EMIF) IP User Guide

6.3.4. DDR4 Interface x4 Data Lane

Agilex™ 5 FPGAs support only x4 components on JEDEC-compliant DIMMs. For DDR4 x4 interfaces, two nibbles must be packed into the same IO12 lane.

Four pins are reserved for DQS_T and DQS_C signals and the remaining eight pins implement the DQ signals. The IO12 lane is divided into upper and lower halves to accommodate each nibble. You cannot swap signals belonging to one nibble with signals belonging to the other nibble. DQ signals within a nibble swap group may be swapped with each other. You may also swap entire nibbles—that is, nibble 0 and nibble 1—with each other provided the DQS pin functionality transfers to the correct pin locations. However, this process is not recommended for JEDEC-compliant DIMM interfaces, as it prohibits the interoperability between DIMMs constructed with x4 components and DIMMs constructed with x8 components.

The following table lists the supported pin functionality in x4 mode and the pins that may be swapped with each other. Pins belonging to the same swap group may be freely interchanged with each other.

Table 77.  Pin Swapping Rules for DDR4 x4
Pin Index Within Byte Lane DDR4 x4 Data Lane Function Swap Consideration
0 DQ Pin (lower nibble) Swap group A Nibble 0
1 DQ Pin (lower nibble) Swap group A
2 DQ Pin (lower nibble) Swap group A
3 DQ Pin (lower nibble) Swap group A
4 DQS_T Pin (lower nibble) Fixed location (not swappable)
5 DQS_C Pin (lower nibble) Fixed location (not swappable)
6 DQS_T Pin (upper nibble) Fixed location (not swappable) Nibble 1
7 DQS_C Pin (upper nibble) Fixed location (not swappable)
8 DQ Pin (upper nibble) Swap group B
9 DQ Pin (upper nibble) Swap group B
10 DQ Pin (upper nibble) Swap group B
11 DQ Pin (upper nibble) Swap group B
  • Nibble 1 must correspond to DQS[17:9] on a physical JEDEC-compliant DIMM for x4/x8 interoperability.
  • Nibbles 0 and 1 must follow the same skew matching rules among all 12 signals in the IO12 lane as are specified for a x8-based DQS group.
Note:
  • Although the current version of the Quartus® Prime software may not enforce all of the rules listed in the above table, be aware that all of these rules may be enforced in later versions of the software.
  • At present, the Quartus® Prime software checks the following:
    • Address and command pin placement, per the table in the Address and Command Pin Placement for DDR4 topic, or the Agilex™ 5 External Memory Interface Pin Information file, which is available here: Pin-Out Files for Intel FPGA Devices.
    • For x8, the Quartus® Prime software checks the following:
      • DQS_T and DQS_C are on pin index 4 and pin index 5 in a byte lane.
      • DM/DBI is on pin index 6.
      • DQ[x] are on pin indices [11:8] and [3:0].
    • For x4, the Quartus® Prime software checks the following:
      • DQS_T and DQS_C on pin index 4 and pin index 5 and associated DQs are within the corresponding byte lane.
      • DQS_T and DQS_C on pin index 6 and pin index 7 and associated DQs are within the corresponding byte lane.
      You are responsible for ensuring that these conditions are met.
  • The Quartus® Prime software does not currently check whether DQ pins associated with the lower nibble DQS are actually placed in pin[3:0] or whether DQ pins associated with the upper nibble DQS are actually placed in pin[11:8].
Level Two Title