Intel® Cyclone® 10 GX FPGA Development Kit User Guide

Download PDF
ID 683696
Date 8/15/2018
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Board
2. Getting Started x
2.1. Installing the Quartus Prime Software 2.2. Development Kit Package 2.3. Installing the Intel® FPGA Download Cable Driver
3. Development Kit Setup x
3.1. Setting up the Development Kit 3.2. Default Switch and Jumper Settings
4. Development Kit Components x
4.1. Board Overview 4.2. Cyclone 10 GX FPGA 4.3. MAX 10 System Controller 4.4. FPGA Configuration 4.5. Status and User I/O Elements 4.6. Clocks 4.7. Memory 4.8. Power 4.9. Transceivers Interfaces and Communication Ports
4.5. Status and User I/O Elements x
4.5.1. Switches 4.5.2. Pushbuttons 4.5.3. LEDs
4.7. Memory x
4.7.1. EMIF with DDR3 4.7.2. QSPI Flash
4.9. Transceivers Interfaces and Communication Ports x
4.9.1. Transceiver Channels 4.9.2. PCIe Interface 4.9.3. SFP+ Interface 4.9.4. USB3.1 Type-C Interface 4.9.5. FPGA Mezzanine Card (FMC) Interface 4.9.6. 10/100/1000Base-T Ethernet Connector 4.9.7. I2C/PMBUS
5. Board Test System x
5.1. Preparing the Board 5.2. Running the Board Test System 5.3. Using the Board Test System
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The System Info Tab 5.3.3. The GPIO Tab 5.3.4. The EPCQ Tab 5.3.5. The XCVR Tab 5.3.6. The FMC Tab 5.3.7. The DDR3 Tab 5.3.8. Power Monitor 5.3.9. Clock Controller
A. Additional Information x
A.1. Safety and Regulatory Information A.2. Compliance and Conformity Statements
A.1. Safety and Regulatory Information x
A.1.1. Safety Warnings A.1.2. Safety Cautions
B. Revision History x
B.1. Document Revision History for Intel® Cyclone® 10 GX FPGA Development Kit User Guide
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

4.5.3. LEDs

The LEDs are on the top side of the board at the upper right corner.

Table 13.  Board LED Definition
Board Reference Signal Name Colour Function
D16 PGM_LED0 Green Image 0 is loaded in FPP mode
D17 PGM_LED1 Green Image 1 is loaded in FPP mode
D18 PGM_LED2 Green Image 2 is loaded in FPP mode
D14 LOAD_LED Green Indicates image is loading
D15 CFGDONE_LED Green Indicates image loading succeeded
D13 ERR_LED Red Indicates image loading failed
D22 USER_LED3 Green '1' to light, output from FPGA
D19 USER_LED0 Green '1' to light, output from FPGA
D20 USER_LED1 Green '1' to light, output from FPGA
D21 USER_LED2 Green '1' to light, output from FPGA
D23 POK_LED Green Indicates power is OK
Level Two Title