System Memory for Intel® Desktop Board DH61ZE

Documentation

Compatibility

000008155

09/27/2017


System memory features
The board has two DIMM sockets and supports the following memory features:

  • Two independent memory channels with interleaved mode support
  • Supports 1.2V–1.8V DIMM memory voltage
  • Support for non-ECC, unbuffered, single-sided, or double-sided DIMMs with x8 organization
  • 16 GB maximum total system memory (with 4 Gb memory technology)
  • Minimum total system memory: 1 GB using 1 Gb x8 module
  • Serial Presence Detect
  • DDR3 1333 MHz and DDR3 1066 MHz SDRAM DIMMs

For full compliance with all applicable DDR SDRAM memory specifications, the board must use DIMMs that support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to correctly configure the memory settings, but performance and reliability can be impacted or the DIMMs might not function under the determined frequency.

1.5V is the recommended and default setting for DDR3 memory voltage. The other memory voltage settings in the BIOS Setup program are provided for performance tuning purposes only. Altering the memory voltage may (i) reduce system stability and the useful life of the system, memory, and processor; (ii) cause the processor and other system components to fail; (iii) cause reductions in system performance; (iv) cause additional heat or other damage; and (v) affect system data integrity.

Intel has not tested and does not warranty the operation of the processor beyond its specifications. For information on the processor warranty, refer to Processor Warranty Information.

Supported memory configurations

 
DIMM Capacity Configuration SDRAM Density SDRAM Organization Front-side/Back-side Number of SDRAM Devices
512 MB Single-sided 1 Gbit 64 M x 16 / empty 4
1 GB Single-sided 1 Gbit 128 M x 8 / empty 8
1 GB Single-sided 2 Gbit 128 M x 16/ empty 4
2 GB Double-sided 1 Gbit 128 M x 8 / 128 M x 8 16
2 GB Single-sided 2 Gbit 128 M x 16 / empty 8
4 GB Double-sided 2 Gbit 256 M x 8 / 256 M x 8 16
4 GB Single-sided 4 Gbit 512 M x 8 / empty 8
8 GB Double-sided 4 Gbit 512 M x 8 / 512 M x 8 16
 

Tested memory

Third-party tested memory
The table below lists parts which passed testing during development. These part numbers might not be readily available throughout the product life cycle.

 
Module manufacturer Module part number Module size Module speed ECC or Non-ECC
ADATA M3OHYMH3J4130G2C5Z 2 GB 1333 MHz Non-ECC
APACER 240P 1 GB 1333 MHz Non-ECC
ELPIDA EBJ10UE8BBF0 1 GB 1066 MHz Non-ECC
ELPIDA EBJ10UE8BDF0 1 GB 1333 MHz Non-ECC
ELPIDA EBJ21UE8BBF0 2 GB 1066 MHz Non-ECC
ELPIDA EBJ21UE8BDF0-DJ-F 2 GB 1333 MHz Non-ECC
Hynix HMT112U6BFR8C-G7 1 GB 1066 MHz Non-ECC
Hynix HMT112U6TFR8C-H9 1 GB 1333 MHz Non-ECC
Hynix HMT125U6BFR8C-G7 2 GB 1066 MHz Non-ECC
Hynix HMT125U6BFR8C-H9 2 GB 1333 MHz Non-ECC
Hynix HMT351U6AFR8C-H9 4 GB 1333 MHz Non-ECC
Micron MT8JTF12864AY 1GB 1066MHz Non-ECC
Micron MT8JTF12864AZ-1G4F1 1 GB 1333 MHz Non-ECC
Micron MT16JTF25664AY-1G1D1 2 GB 1066 MHz Non-ECC
Micron MT16JF25664AZ-1G4F1 2 GB 1333 MHz Non-ECC
QIMONDA IMSH51U03A1F1C 512 MB 1066 MHz Non-ECC
QIMONDA IMSH1GU13A1F1C 1 GB 1066 MHz Non-ECC
SAMSUNG M378B2873EH1-CF8 1 GB 1066 MHz Non-ECC
SAMSUNG M378B22873DZ1-CH9 1 GB 1333 MHz Non-ECC
SAMSUNG M378B5673DZ1 2 GB 1066 Mhz Non-ECC
SAMSUNG M378B5673FH0-CH9 2 GB 1333 MHz Non-ECC
SAMSUNG M378B5273DH0-CH9 4 GB 1333 Mhz Non-ECC