System Memory for the Intel® Desktop Board DH61WW

Documentation

Compatibility

000005810

09/26/2017

System memory features
Supported memory configurations
Tested memory


System memory features
The board has two DIMM sockets and supports the following memory features:

  • Two independent memory channels with interleaved mode support
  • Supports 1.2 V – 1.8 V DIMM memory voltage
  • Support for non-ECC, unbuffered, single-sided or double-sided DIMMs with x8 organization
  • 16 GB maximum total system memory (with 4 Gb memory technology)
  • Minimum total system memory: 1 GB using 1 Gb x8 module
  • Serial Presence Detect
  • DDR3 1333 MHz and DDR3 1066 MHz SDRAM DIMMs

To be fully compliant with all applicable DDR SDRAM memory specifications, the board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to correctly configure the memory settings, but performance and reliability may be impacted or the DIMMs may not function under the determined frequency.

The recommended and default setting for DDR3 memory voltage is 1.5 V. The other memory voltage settings in the BIOS Setup program are provided for performance tuning purposes only. Altering the memory voltage may (i) reduce system stability and the useful life of the system, memory, and processor; (ii) cause the processor and other system components to fail; (iii) cause reductions in system performance; (iv) cause additional heat or other damage; and (v) affect system data integrity.

Intel has not tested and does not warranty the operation of the processor beyond its specifications. For information on the processor warranty, refer to Processor Warranty Information.

Supported memory configurations

DIMM Capacity Configuration SDRAM Density SDRAM Organization Front-side/Back-side Number of SDRAM Devices
512 MB Single-sided 1 Gbit 64 M x 16 / empty 4
1 GB Single-sided 1 Gbit 128 M x 8 / empty 8
1 GB Single-sided 2 Gbit 128 M x 16 / empty 4
2 GB Double-sided 1 Gbit 128 M x 8 / 128 M x 8 16
2 GB Single-sided 2 Gbit 128 M x 16 / empty 8
4 GB Double-sided 2 Gbit 256 M x 8 / 256 M x 8 16
4 GB Single-sided 4 Gbit 512 M x 8 / empty 8
8 GB Double-sided 4 Gbit 512 M x 8 / 512 M x 8 16
 

Tested memory

Third-party tested memory
The table below lists parts which passed testing during development. These part numbers may not be readily available throughout the product life cycle.

Module manufacturer Module part number Module size Module speed ECC or Non-ECC Component manufacturer Component part number
ADATA* AX3U1600GB2G9 -2G 2 GB 1600 MHz Non-ECC    
ELPIDA* EBJ10UE8BBF0 1 GB 1066 MHz Non-ECC   084909K2500
ELPIDA EBJ10UE8BBF0 1 GB 1333 MHz Non-ECC   084909K2500
ELPIDA EBJ21UE8BBF0 2 GB 1066 MHz Non-ECC   0905AXA9062
ELPIDA EBJ10UE8BBF0 2 GB 1333 MHz Non-ECC   084909L9500
Hynix* HMT112U6BFR8C 1 GB 1066 MHz Non-ECC Hynix H5TQ1G83BFR G70 912A
Hynix HMT112U6BFR8C 1 GB 1333 MHz Non-ECC Hynix H5TQ1G836BFB H9C 909A
Hynix HMT125U6BFR8C 2 GB 1066 MHz Non-ECC Hynix H5TQ1G83BFR G7C 910A
Hynix HMT125U6BFR8C 2 GB 1333 MHz Non-ECC    
KINGSTON* HP497156-C01-ELB 1 GB 1333 MHz Non-ECC ElPID J1108BBSE DJ-F 0903R90E300
KINGSTON BSME1630931 2 GB 1333 MHz Non-ECC ElPID J1108BABG DJ-E 085009D2C
Micron* MT8JTF12864AZ 1 GB 1333 MHz Non-ECC 90F22 D9KPT
Micron MT16JTF25664AY 2 GB 1066 MHz Non-ECC 8ZD22 D9JNL
Micron MT16JTF25664AZ 2 GB 1333 MHz Non-ECC 90F22 D9KPT
QIMONDA* MSH51U03A1F1C 512 MB 1066 MHz Non-ECC IDSE1S-03A1F1C-10F FSB31577
QIMONDA IMSH1GU13A1F1C 1 GB 1066 MHz Non-ECC IDSH51-03A1F1D-10F FSS36541
QIMONDA IMSH2GU13A1F1C 2 GB 1333 MHz Non-ECC IDSH1G-03A1F1C-13H Fss15499
SAMSUNG* M378B2873EH1 1 GB 1066 MHz Non-ECC SEC 849 HC F8 K4B1G08461
SAMSUNG M378B2873DZ1 1 GB 1333 MHz Non-ECC SEC 916 HC H9 K4B1G08460
SAMSUNG M378B5673EH1 2 GB 1066 MHz Non-ECC SEC 846 HC F8 K4B1G0846E
SAMSUNG M378B5673DZ1 2 GB 1333 MHz Non-ECC SEC 843 HC F8 K4B1G08410